AH-6J Little Bird
The AH-6J Little Bird is used by Task Force 160th SOAR as a fast attack aircraft. During the Somalia mission, it was the Little Birds job to keep the hordes of Somalis from overrunning the Rangers overnight. There speed and stealth made them perfectly suited to provide rocket and gun support.
Prior to this release, the only way to get a Little Bird was to use the Hasegawa kit and the CMK conversion set. This was very expensive and sometimes difficult to find. The AH-6/MH-6 are very small aircraft, especially in 1/48th scale.
Packaged inside the sturdy cardboard box with a box top sleeve are five sprues of light grey plastic and one sprue of clear parts. The parts are TINY, so care must be taken to not feed the carpet monster. Sprue A and B are the same sprues as in the MH-6J kit. Actually all the parts to do an MH-6J are in this box. The raised rivet detail is the finest I’ve ever seen. Impossible to replace so take care. Sprue D has gunship specific items such as the bench and ammo box, along with the downturned exhaust. There are two Sprue Es, which has the actual armament, such as miniguns and rocket launchers. There is no flash or mold marks on anything in my box. You get the armament option of M-134 miniguns, GAU-19 .50 Cal, M-260 seven-shot and M-261 19-shot rocket pods.
There are somethings that are missing in the kit, most notably is the lack of ammo chutes for the guns and the seatbelts. They are both highly visible. The ammo chute comes out of the ammo can into the gun. Some other minor things missing are the first aid kit and fire extinguisher. There is also a structure in the backseat on the back of the pillar that is missing. It is tough to see, but adds to the look of the armed aircraft. I’ll touch on each thing as I go along.
The instruction booklet is broken down into 88 steps. They are easy pictures to understand and in a logical order. There is a small decal sheet that has markings in olive drab and flat black, along with the personal markings of some different aircraft.
First off is to decide which timeframe you want to represent. I wanted to do one of the Somalia aircraft. Since Barber 51 had a FLIR and mount on the nose, I opted to do Barber 52. Barber 51 was the only aircraft with the FLIR. Next, I had to look over the photos I had for the antenna arrangement for 1993.
For the Somalia AH-6Js, here is what I elected to use based off of my research. I go through my instruction booklet and X out the ones I don’t need to use.
- Step 4- I did not use the extra internal fuel tank. I do not believe they used them in Somalia. I could be wrong.
- Step 12-B50, B4, B18, B38. Do not use B9. I can not see that standoff for the position lights on the aircraft during that time. You will need to remove the mount on the airframe as well.
- Step 29- B3, B18, B51. Again, don’t use B9.
- Step 30B is what you’ll need for a Somalia aircraft. The attack assets had the downturned exhaust.
- Step 45- B40, B41, B42
- Step 47- B1
- Step 58- B63, A45
- Step 61- A39, B62
- Step 73- Don’t use
- Step 74- B44, B45
- Step 75- B49
- Step 77- B1
The armament for Somalia was M-260 seven shot rocket pods on the outboard mount and M-134 miniguns on the inboard. So with all that sorted out it was time to start the build.
As usual the build starts in the cockpit. Everything fits perfectly if you remove all the sprue attachment points. The interior and the whole aircraft is flat black. The challenge here is to add tonal variations to add visual interest. I did it by using two versions of NATO Black, Tamiya and MRP. I also used very dark greys. I added weathering to the floor to add authenticity. I added Eduard photo etch seatbelts (FE1586) which fit perfectly; however, they really should go behind the bulkhead to inertia reels. These will only fit behind the seat backs A30. It isn’t perfect but looks convincing enough. Again, I left off the fuel tank from Step 4. I do not believe they used them in Somalia.
Don’t forget to open up some holes for the various antennas, bench support and air intake. When I was happy with the look of everything I added the cockpit to the one fuselage halve. Make sure that the floor and back bulkhead sits perfectly in the fuselage.
Building up the rotor controls is an exercise in patience and understanding. Go slow and pay attention to the instructions. If done correctly, the fit is perfect. Again, there a lots of small parts here, especially B2. I did have to hollow out part B19 and A1 with a file to fit the mast assembly, A3. I did NOT add the mast assembly at this time, which meant leaving off part B53. I left the mast off until much later in the build. It just makes handling it so much easier.
Before bringing the fuselage halves together, I added a bracket from Ramon Lomeli tp the back seat area. It did need to be cut down slightly to fit but noting too drastic. Its hard enough to see since its painted black in a black helicopter. It added additional visual interest. Don’t forget to add part B31 and the appropriate exhaust before closing up the halves. In the case of Somalia, the downturned exhaust was used. I found it to be a little thick. Hopefully an aftermarket company will produce a replacement.
Building up the instrument panel and center console is easy enough. Care must be taken especially when building up the cyclic control sticks. They are fragile and care must be taken when cleaning and building them up. One thing I did do that I learned after building up the MH-6J, was to sand the heck out the front of the console, A25 and A34. This will ensure that the canopy fits perfectly. I used the kit decals for the center console. They fit will and settled down with strong setting solutions. The parts that gave me the most headache were also some of the smallest, the tail rotor pedals. I recommend that you add the horizontal part while the vertical one is still attached to the sprue. This made it simpler but you have to pay attention to the orientation of the two parts. Leave them on the sprue until you are ready to install them.
I opted to add the armament bench with the ammo box at this time as I was able to manipulate it into position and glue it. The ammo box build up is in Step 54 and 55.
Then it was time to bring the fuselage halves together. The fit was perfect. The one thing about ICM is that they do NOT add rivet detail on the bottom along the seam. This is helpful when cleaning up the seam. I used a rivet tool to add some recessed rivet detail. It was basically connecting the rivet lines on one side to the other. It works. Rivet decals would have been hugely out of scale.
Time to add the windscreen. Don’t forget to paint the inside of top of the canopy smoke. It isn’t green it is tinted smoke. Prior to adding the canopy, I recommend that you paint the inside of the attachment points with a black Sharpie. This takes away the ‘plastic’ look of the canopy. Gluing the canopy is easy but pay attention as much of the canopy goes to the outside with no frame. When adding the glue ensure you only touch the places where the framing is. That is the top center, center of the sides and the bottom in the middle. The fit is perfect or as near as perfect as you can get.
The landing gear is next up. I did alter this procedure slightly. I added the toe portion of the skids prior to adding the gear to the helicopter. This allows me to manipulate the parts to get a perfect fit. Adding the landing gear to the helicopter provides a very positive fit that ensures the model sits perfectly. Just align the front and back and a touch of glue. Then just wait until it sets up permanently.
While that is drying, you can build up the tailboom and tail rotor gearbox. The gearbox in Step 52 requires careful dry fitting and understanding what is happening to get it correct. Using a square makes sure that the tail vertical and horizontal pieces are straight. They are just butt joints so care must be taken when building them up. Allow them to dry thoroughly. All of this was added to the fuselage. The fit was perfect as was the alignment.
Now came time to build up the M-134s. This is the only place in the instructions that I had some questions. I eventually figured it out the placement of the gun motor and associated motors. Adding the barrels was a big pain. There are three pieces to the barrels themselves. I recommend that you mark them on the inside with a marker to keep track of which side is the inside. I got them to work well enough but they are missing the flash suppressors on the end. I had some M-134 barrels from Black Ops 3D Productions with the proper suppressors and elected to use them instead. I could have easily lived with the kit guns but since I had the correct ones, why not?
I built up the M-260 seven-shot rocket pods, as well as the 19-shot pods and the GAU-19. The fit of everything was fabulous. The GAU-19 was spectacular and I’ve saved them for an OH-58D Kiowa Warrior build in the future. I added the sway braces to the kit M-260s as they fit perfectly and ensured a solid join. I was debating using a Werner’s Wings M-260 but the kit ones were adequate and looked the part. All armament was left off until the end of the build.
Time to paint, but first I used Eduard EX1173 masks for the canopy. They fit perfectly and emphasize the point that the windows don’t have framework all the way around. I used small pieces of tape on the inside of the canopy to alleviate any overspray or frosting. The kit doors for the front and the back were attached with MicroMask. This saved me from having to stuff the huge doors with tape or some other method. The back doors don’t fit all the way down so that was stuffed with some foam to prevent the paint going inside. In Somalia they did not use front or back doors so I wouldn’t need them.
I tried Gunze Mr Primer 1500 black with Mr Leveling Thinner for the first time. It worked well. I only had one place that needed touch up. Once that was taken care of I painted the model with MRP NATO Black. It was tough to tell the difference but it was enough to build off of. Some Tamiya NATO Black was added here and there, because it was slightly different shade. Also some MRP Gunship Grey was sprayed on the top surfaces to highlight the sun beaten look of the black. Additional highly thinned Tamiya Buff was sprayed on some area that would get dirty and accumulate dust. A coat of Tamiya Clear thinned with Mr Leveling Thinner made the kit ready for decals.
The kit decals worked flawlessly. The markings are mostly black and surprisingly they show up pretty well on the NATO Black. I used the Harley Davidson emblem on the nose along with the olive drab tail number, 362. I did not like the kit white markings for the rocket pods so I used a 1/72nd scale sheet from Werner’s Wings for the rocket stencils which was the proper color. Everything was sealed with a gloss coat and then a flat coat.
Let the weathering begin. I used AK Panel Liner for Black Camouflage (AK2075) to highlight some panels and to fade the black. First I added a small dot here and there then using Mineral Spirits I swirled the color around and then streaked it downward to show wear and rain marks. Tamiya Black Panel Liner was used on various panels to change their tone and show some touched up paint. AK Oil Brusher Starship Filth was added around certain panels that would be handled by ground crews added another depth. Chipping was added with a #2 pencil and very sparingly with a silver pencil as silver is just too stark. Some Tamiya weathering powders finishes up the weathering. I thought I had gone a little too far so I hit the entire model with a flat coat to tone everything down.
Pulling off the canopy masks and the doors revealed a beautiful finish. The only thing left was to attach the armament. The guns fit perfectly. Then I added the Mini World Ammo Chutes (A4853a) for the 7.62. They have to be cut to length and then folded. I used black superglue to attach them in place. The rocket pods were added to the end of the bench.
Other than adding the tail and main rotor the model was done. The tail rotor fits nicely in place which has a shallow cutout for the crosshead. Make sure you align it properly. The main rotor was just slid into position. ICM would have you add white decals on the top of the main rotor blades. That is not required. I’ve never seen those markings.
The fit of this kit was exceptional throughout. There are some omissions but overall the kit is fabulous. I’ve now built the MH and AH-6J and find them a lot of fun. There are a lot of small parts so make sure you have an Optivisor and good tweezers, but the end result is far superior to the previous conversion set. I thoroughly enjoyed the build. I hope they do an MH/AH-6M as well. All the aftermarket stuff was a good addition and everything fit there as well. Another great kit from ICM. They keep moving from strength to strength.
Highly recommended
Thanks to ICM and IPMS/USA for the review copy.
Reviewer Bio
Floyd S. Werner Jr.
Building models since the age of 7, I’ve become known for my Bf-109s and helicopters. I currently run Werner’s Wings. I was previously the ‘star’ of the Master Class Model Building Video series. I’ve been published numerous times on various website, including Hyperscale and ARC. My work has been in FSM and Great Scale Modeling 2001, as well as, numerous other model magazines. I’m a published author with my Squadron/Signal Walkaround book on the Kiowa Warrior. My models have continuously won many regional and national awards. My unique model photography gives my models instant recognition for their historical perspective.
I’m a retired from the Army after 21 years of flying Cobras and Kiowa Warriors, including tours in Iraq, Bosnia, Korea, and Germany. I’m also a retired Flight Officer for the Baltimore City Police and flew their helicopters chasing bad guys. I’m currently flying Cobras and Hueys with the Army Aviation Heritage Foundation.
I’ve been married to my high school sweetheart, Yvonne, for 42 years. Our daughters have blessed us with six grandchildren. My passions continue to be his family, friends, helicopters, models and airplanes, especially the Bf-109 and my beloved AH-1 Cobra. My motto has always been - MODELING IS FUN!

Comments
Add new comment
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Similar Reviews