This is a photoetch Interior set to for the Hong Kong Models B-17 E/F Kit number 01E04a. This set with two photoetch sheets one is colored and adds a lot of needed detail to the Nose compartment of the B-17. These parts really add some great additional details to an great kit.

In the packet is:

• 1 colored photoetch sheet
• 1 photoetch sheet
• 1 instruction sheet

Summary

This is a fantastic set for the set for a kit that is great to begin with, these parts are an awesome addition.

I did find a few minor issues with the set and also with the main kit instructions;

The Falanga 9M17P Flite (NATO reporting name of AT-2 Swatter) is a radio controlled anti-tank missile developed by the Soviet Union. It was one of the standard weapons fit of the Hind A and Hind D helicopter gunships used in the Soviet Union, many Eastern Europe countries and others that operated the Hind A and Hind D helicopters. The missiles were normally mounted in pairs on each side of the helicopter. The launch rails usually mounted at bottom of the end plates on the Hind’s stub wings. The missiles were also mounted on several types of armored personnel carrier of the BRDM series.

Eduard has released a full line of Hellcats in 1/48 scale, covering from the early -3, to the late -5, including night fighter versions and even Royal Navy service markings. This particular boxing is the Weekend edition of the -5(N), with neither mask nor photoetch, but with two options for decals and a small number of resin parts to make the conversion to “night fighter”.

When I opened the box I found a total of 5 sprues (one clear) and 3 small resin casting for details like radio-altimeter, exhausts, radar housing for the starboard wing and cannons with nicely casted flash dampers. FYI: the nightfighter version of the Hellcat was capable of carrying a 20 mm cannon.

A note on the sprues: one of them –the fuselage one- was molded in tan, while the rest of the sprues were molded in blue-gray. And there were two full engine cowlings, but no indication of the second cowling in the instructions. I was a bit puzzled by the different plastic colors and two cowlings.

Master Model of Poland produces small brass parts for detailing models, be they aircraft or ships. They have parts for aircraft in 1/32, 1/35, 1/48, 1/72, and 1/144, mostly pitot tubes, refueling probes, and gun barrels.

The pitot part is a very fine piece of brass. The piece is much finer than the kit part.

I didn’t have a 1/144 Hunter on the shelf, so this review required that I build the Revell Hunter. As long as I’m building it, I may as well do it as part of my “Suez 1956” project. That’s why the Hunter has those red and yellow stripes, negating any camouflage effect.

Pitot Installation

Once the kit was almost finished, I got out the Master Model pitot and took the pictures. It was an easy installation. Revell gives you a little notch at the wing tip, and the CA provides a bit of filler. I then painted the pitot silver. No drilling, just a bit of CA and accelerator.

Overall Evaluation

Highly recommended.

With the recent releases of the special edition F-104 kits from Eduard in 1/48 using Hasegawa plastic, Eduard has released the F-104 C2 ejection seat as a separate kit. The Lockheed C2 ejection seat was the most commonly used ejection seat for the F-104 in US service. It is a downward firing rocket propelled ejection seat.

This seat set is very simple. It contains the main seat frame, two seat options, rails, a small photoetch set and a small decal set. As this is a drop in replacement seat for the kit seat the assembly is very straight forward. Everything in the kit replaces the equivalently parts in the F-104 kit. The first step in the assembly is to remove the three large resin parts from the casting blocks, using a razor saw for this step. If you are careful minimal clean up will be needed. After clean up, wash the parts to remove the mold release agent that is often on resin parts.