Brengun, from the Czech Republic, specializes in aftermarket details; for the most part releasing drop-in resin or photoetch replacement parts.

This set is intended to enhance the 1/48 Skyhawk A-4 C/E/F/M. This set can be used with any of the 1/48 Skyhawk kits, like the Hasegawa, ESCI/AMT/Italeri, Hobbycraft, HobbyBoss, or Monogram. If I am missing any other maker in the list, it is an honest mistake on my end.

Please note that the instructions list the variant of the airplane to be in 1/72. That is clearly a mistake, this set is molded in 1/48 scale.

The parts are molded in grey resin, free of bubbles or imperfections and with great surface detail. The attachment points to the casting blocks are miniscule and removal and clean up should be an easy task.

I do not think the RATO rockets saw widespread use in the Skyhawk fleet, so you might want to do some research as to which version, or even down to tail number you are modeling.

There are numerous accounts of the various armoured campaigns that defined the major fronts of WWII from the perspectives of all sides involved. Some are exhaustive accounts filled with places, dates, and names that can be excruciating at times to read with the extensive details. Books by Anthony Tucker-Jones usually are a bit easier to decipher and can be enjoyable without getting too much into the minutiae. This book is a good example of this- to the point of being a bit watered down perhaps. The book looks at the entirety of the war from the Allied view-- with the book covering American, British and Commonwealth, and French armor forces and that is no small feat.

From Italeri: The Tornado Gr.4 arose from a collaborative project between Italy, Germany, and the United Kingdom for the production of a multi-role high-performance combat aircraft. The primary requirement, however, was to develop a ‘state of the art’ modern aircraft able to perform low-altitude penetrating strike missions. This need was met by the development of a twin-engine combat aircraft with a variable-sweep wing. The Tornado IDS (Interdictor / strike) was the first version to be released by the British Royal Air Force and designated GR.1. In 1996 the Tornado was upgraded to the Gr.4 standard which was characterized by improved operational capabilities, new avionics systems for navigation and the adoption of new ‘on-board’ technologies. These systems enabled the effective identification and tracking of targets, and also the weapons management of the newer generation of weapons such as Paveway IV bombs and Storm Shadow cruise missiles.

Bottom Line Up Front: Even though Tamiya’s “new tool” release of the venerable Panzerkampfwagen IV does not disappoint with nice detail, clever engineering, and three figures that are well rendered in unique and interesting poses. Even though this kit uses the hull and suspension from the 1994 Panzer IV releases, the vast majority of the kit is brand new and up to modern standards. This is not merely a reboxing of an old obsolete kit.

History

The Pz.Kpfw.IV began manufacture in 1936 with the Ausf. A, and went through a number of specifications before what was perhaps the definitive short barreled infantry support variant started production in 1941: the Ausf. F. It had reinforced armor and updated hull designs, as well as an L/24 75mm gun. About 460 rolled off of the production lines, mostly serving on the Eastern front but also in North Africa, Italy, and France.

Aerobonus is part of Aires and focuses on enhancement additions such as pilot figures for kits. This product provides a pilot figure seated, in 1/32^nd scale for the Trumpeter/Revell P-51B/C Mustang. The set comes in four parts (head, hands, and set/body) all perfectly cast on a single block. Preparation was easy by using a razor saw to cut all the parts free (after a good washing). I then used the back of a #11 blade to scrape what few seams there were and glued everything together. I used perfect plastic putty on the arm seams and wiped with water and the seams were gone. I primed with Alclad gray primer.

Painting was done with acrylics using Scale 75 for the flesh and various sources for the rest. The seat was painted with ModelMaster paints. As you can see from the included paint guide, you need to look on the internet to get more specific but with all the references, it was not too difficult. A final flat coat and the project was done.