Welcome to the IPMS/USA Reviews site!

Introduction: The primary organization of the IPMS/USA Review website is by IPMS/USA National Contest Class. Within each Class there are sub-menus by kits, decals, books, etc. The Miscellaneous Class is for items that are not class specific or that cross two or more classes.

IPMS/USA Members: We encourage you to submit reviews, both here and to the Journal. To volunteer for membership in the IPMS/USA "Reviewers Corps" and submit your own reviews, please read the Guidelines For Submitting Product Reviews.

Manufacturers, publishers, and other industry members: IPMS/USA is pleased to offer your company the opportunity for product reviews. All product reviews are performed by IPMS/USA members, and are posted in the publicly-accessible section of our website. With very few exceptions, we perform full build reviews of new kit releases, aftermarket products, and supplies. If you would care to provide product samples for review, please contact John Noack, IPMS/USA 1st VP.

To learn more about IPMS/USA, please see our About Us page.

Book Author(s)
John Adams-Graf
Review Author
Bill O'Malley
Published on
Company
Squadron Signal Publications
MSRP
$18.95

This is another book in Squadron Signal’s In Action series that profiles a family of military vehicles with photos of them in actual use. The series uses in-field photos to trace the history and development of the vehicles.

The history of Mine-Resistant Ambush-Protected (MRAP) vehicles is chronicled from the earliest armored security vehicles (ASVs) that were built to replace armored HMMWVs and provide greater resistance to roadside bombs and Improvised Explosive Devices (IEDs) during the Iraq wars.

Review Author
Jim Pearsall
Published on
Company
Master Model
Scale
1/72
MSRP
$5.50

This accessory is for the Heller Tunnan kit. The parts are replacement pitot tubes.

The Kit

You get two finely done brass parts in a plastic envelope, which is inside another plastic envelope. Good plan – lost parts of this size would be a disaster, not to mention impossible to find. I liked the instruction sheet, it was simple, to the point, and uncluttered.

Assembly

I used a Tunnan I built several years ago. It was great to have these brass pitots, as the plastic ones had been broken off soon after I did the model.

I cut off the little projections where the pitots had been earlier and drilled tiny holes in the wing leading edge.

I painted the brass parts with Testors Aluminum Metalizer.

There is a difference between the left and right pitots, and the instructions are VERY specific about which is which.

A bit of gel-type CA, and a bit of touch up, and the project was finished.

Review Author
Brian R. Baker
Published on
Company
Azur
Scale
1/72
MSRP
$27.00
  • Azur MS-406C.1, Stock #A109, $27.00
  • Azur MS-410C.1, Stock #075, $27.00

History

The Morane Saulnier MS-406 series of single seat fighters originated in 1934 after a design competition, with the MS-405C.1 eventually being ordered into limited production in 1937; only 16 were produced. During that year, minor modifications were made, with subsequent Morane fighters receiving the designation MS-406C.1. Initially, 50 and 80 MS-406’s were ordered on different contracts, and with the threat of war looming, an additional 825 were ordered from the SNCAO factory during May, 1938. Production ended in March, 1940, with 1079 MS-406’s being produced. A number of developmental aircraft were considered, using different armament and engine combinations, but the only one to enter production was the MS-410C.1, which featured a revised radiator and additional armament. After the surrender in 1940, 11 MS.

Review Author
Greg Wise
Published on
Company
Quickboost
Scale
1/48
MSRP
$6.50

The Product

My sample arrived packaged in the all-too-familiar orange-topped poly sleeve with the typical card insert. After close inspection of the parts, I found them to be perfect. As you can see, the kit parts offer excellent detail; even so, the Quickboost seats are by far superior in detail, and they’re a drop-in replacement. They are easily detached from the pour block and clean up with a few swipes from a sanding stick.

The Bottom Line

I recommend these babies to anyone wanting to enhance his Ju-52 build.

Thanks to, Aires/Quickboost and IPMS for the opportunity to review these nice little castings.

Review Author
Greg Wise
Published on
Company
Quickboost
Scale
1/48
MSRP
$6.50

The Product

My sample arrived packaged in the all-too-familiar orange-topped poly sleeve with the typical card insert. After close inspection of the parts, I found them to be perfect. These little beauties are just what the Doctor ordered. They’re a drop-in replacement for the kit parts. They’re easily detached from the pour block and ready to install. How easy is that?

The Bottom Line

I recommend these babies to anyone wanting to enhance his Skyraider build.

Thanks to, Aires/Quickboost and IPMS for the opportunity to review these nice little castings.