The Aircraft

The B-52 has been flying longer than a lot of IPMS members have been building. It entered USAF service in 1955, and 85 of them are still in active inventory, with 9 in reserve. The combat-ready B-52Hs left are at Minot AFB in North Dakota and Barksdale AFB, Louisiana.

The Scale Aircraft Conversions set

The SAC set for the B-52 consists of 4 identical main gear sets and two outrigger wheels and struts for the wings, all in white metal. The outriggers are cast with a protective sprue, which is a great idea since they’d be a little fragile.

The main gear uses the kit wheels.

Painting

This was pretty simple. The main gear and the outriggers are painted white. I used Floquil Reefer White, which goes on nicely from the airbrush and sticks wonderfully to the metal parts. I then brush-painted the wheels on the outriggers with Floquil Grimy Black.

Dragon's latest Stug III release is marketed as a December ‘44 production time frame version. If you follow the instructions, you won't build a vehicle from the Dec 44 production run, but a somewhat jumbled mix with early, mid, and late production features. Fortunately, if you know what you are looking for, the kit includes the parts to build what is commonly accepted as a late ‘44/early 45 vehicle. With some exceptions.

The parts are molded in light gray styrene with crisp details and no noticeable flash. There are some very fine details like the fender tread pattern, hull weld beads, and rough texture on the cast mantle (Topfblende). This release is a bit of a mix-and-match from their earlier StuG III releases (notably the CH May ‘44 Mid-Late Production) with a few additional sprues from their StuG IV kits. A good portion of these parts won't be used and are blued out on the front instruction sheet. But don't be too hasty, you'll need some of those pieces.

Quickboost makes another addition to its sets for the Kinetic 1/48th EA-6B Prowler with a replacement set of air scoops. There are 10 different scoops cast perfectly in the expected gray resin.

There are three different varieties of scoops:

• Part 1 replaces kit parts (two scoops) C15+C17/C17+C18
• Part 2 replaces kit part C11 in six scoops
• Part 3 replaces kit part C21 in two scoops

Using the set is simple – cut from the casting block, make sure the bottom edge is good, and glue in place and paint. The Quickboost parts have good depth to the openings, which is not the case with all the kit parts. Also, the kit’s two large scoops have to be glued together and sanded, which is not done with the Quickboost set.

Overall, a good upgrade for the kit parts. Simple and easy to execute, reasonably priced, and also an improvement in accuracy. Recommended to all fans of the Prowler and those wanting that extra detail.

Although too late for World War 2, the de Havilland Vampire served in front-line RAF squadrons until 1953 and in training squadrons until 1966. The Vampire was the RAF’s second jet-powered aircraft, after the Gloster Meteor. Over 3200 copies were manufactured in numerous variants. The FB.5 was a single-seat fighter-bomber, of which over 1000 were built. It was powered by a de Havilland Goblin II turbojet, and it could reach a maximum speed of 550 mph.

Cyber Hobby’s new Vampire comes shortly after their Meteor, Sea Venom, and Sea Vixen, as they continue to build on their line of post-war aircraft. As a new tooling, the kit makes extensive use of slide-molding. The kit comes in the standard Dragon/Cyber Hobby top-opening box, with images on both the box top and bottom. Forty-five parts are included on three sprues, including one in clear, and are molded in light gray. The sprues are individually sealed in clear cellophane.

Quickboost has issued a replacement "tail wheel" for the Kinetic S-2 tracker. It really isn't a tail wheel, but rather a tail skid. The parts are three – a tail wheel, the skid, and the piston. It is well cast in Quickboost’s gray resin. You separate the parts from the casting blocks, sand the minimal attachment points, and assemble the wheel by adding the separate tire.

One thing to note in the comparison photos is how blob-like the kit parts are – almost no detail whatsoever. The kit part is molded as one piece, lacks any wheel hub detail, and will also need filling as there are definitely some sunken-in areas.

If you are building this kit, this part is a must-have! It is recommended, especially due to the low cost and improved detail. My thanks to Quickboost and IPMS/USA for the chance to review this excellent item.