Shaders – Candy Red, Orange, Yellow, Violet

Published on
Review Author(s)
MSRP
$2.38
Product / Stock #
A.MIG-0868/0850/0867/0859
Company: AMMO by Mig Jimenez - Website: Visit Site
Provided by: AMMO by Mig Jimenez - Website: Visit Site

If reading this review feels a little like deja vu all over again, I previously reviewed five of the Shaders, and as four additional colors were still waiting for analysis, I volunteered to help out. Fortunately, I cannot plagiarize myself, so writing this was very easy indeed. Now go ahead and enjoy my assessment of some additional Shaders colors.

A recent arrival for the Review Corps were Shaders from Ammo by Mig Jimenez, which are a unique addition for modelers of just about anything. For this review in particular, I was provided with four of the colors including Candy Red (0868), Orange (0850), Yellow (0867), and Violet (0859). The full line consists of 20 different colors. The Shaders are unique to begin with as they are packaged in 10ml bottles, so they are about half the size of a typical bottle of acrylic paint. Shaders do not require shaking prior to use (they are about the consistency of ink), and they can be mixed to create different shades, and may be thinned with water if desired.

For this review I used only two drops of each of my four Shaders, and this was enough of the product to cover approximately 2 square inches. I primed the outside of an upper scrap fuselage with Stynylrez White, Metal, and Red-Brown. I used pieces of Post-it notes to mask over the Shaders with no issues of lifting. These colors do need to be over sprayed with a clear coat once they are dry in order to seal them.

I mentioned these as being useful to modelers of just about anything, so here are some potential uses:

  • Panel lines on aircraft
  • Shadows on vehicles or buildings
  • Shading (adding tonal variations to paint)
  • Representing sheer fabrics on figures
  • Filters for any subject (with the advantage of being applied with an airbrush)
  • Creating gold mylar (think Apollo Lunar Module and the like)
  • Creating the appearance of heated metal

In watching some available YouTube videos, aircraft, armor, railroad buildings, figure, and Gundam kits are all mentioned. When I volunteered for these colors, I was thinking of using the Candy Red, Orange, and Yellow for shading flames on monster kits. As you can see in my photos, the Shaders did a nice job of adding different tones to the Red-Brown primer, which would be good for showing different shades of rust, and also the effects of the Shaders on Metallic paint.

Based on an early YouTube video on the Shaders as well as a new video added not long ago in English, here are some things to keep in mind when using this product.

  • Start with light shades (you can only make base colors darker with these).
  • Shaders are meant to be applied with an airbrush.
  • Only a few drops are needed to cover a large area.
  • Mig recommends having decals in place before using the Shaders.
  • Excess accumulation will result in a glossy appearance.
  • Shaders are meant to be applied over a flat finish.
  • If a mistake is made, these colors may be wiped off with water (I validated this when I made a mistake on my initial application of the Yellow Shader over the White primer).
  • If adding more layers of Shaders, flat coat the underlying layer first.
  • Coat the Shaders with a gloss or semi-gloss coat prior to adding washes.
  • Your airbrush can be cleaned with water.

My plusses are the unique finishes that you can obtain with the Shaders whether adding shadows, panels of different tones, color differences along panel lines, or creating a new color on a piece of plastic. The unique bottle design is intentional so that these are not confused with other acrylic paints as these are not intended to be used as base colors. With a nice range of colors, you can achieve different effects, and you can easily mix even more colors yourself. I had one minus with this group of Shaders as my Orange looks eerily similar to my Yellow. I did shake the Orange Shader in an attempt to mix the solution in case that was the issue, but this did not change the outcome.

In conclusion, I would highly recommend these paints to anyone wanting to add another option when creating shadows, panels with different tones, or any other effect mentioned. Mig mentions that he created the Shaders to make modeling easier, and he hit the mark with this product. Modelers with some experience with their airbrush should have no issues with using the Shaders.

I would like to thank the folks at Ammo by Mig Jimenez for being gracious enough to provide these Shaders to the IPMS-USA for review! Thanks to Phil Peterson for running the Review Corps and the other folks behind the scenes publishing the reviews. Finally, my sincere appreciation to all who take the time to read this.

Shader Bottles

Comments

Add new comment

All comments are moderated to prevent spam


This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.