Welcome to the IPMS/USA Reviews site!

Introduction: The primary organization of the IPMS/USA Review website is by IPMS/USA National Contest Class. Within each Class there are sub-menus by kits, decals, books, etc. The Miscellaneous Class is for items that are not class specific or that cross two or more classes.

IPMS/USA Members: We encourage you to submit reviews, both here and to the Journal. To volunteer for membership in the IPMS/USA "Reviewers Corps" and submit your own reviews, please read the Guidelines For Submitting Product Reviews.

Manufacturers, publishers, and other industry members: IPMS/USA is pleased to offer your company the opportunity for product reviews. All product reviews are performed by IPMS/USA members, and are posted in the publicly-accessible section of our website. With very few exceptions, we perform full build reviews of new kit releases, aftermarket products, and supplies. If you would care to provide product samples for review, please contact John Noack, IPMS/USA 1st VP.

To learn more about IPMS/USA, please see our About Us page.

Review Author
Robert Folden
Published on
October 13, 2011
Company
Aires Hobby Models
Scale
1/32
MSRP
$36.00

NOTE: Two cockpit sets are virtually the same, with only a few parts different.

To go along with Aires’ new A6M5 Zero wheel bay set, Aires released two cockpit sets. The sets are virtually the same, and are intended for use with the same base kit. The differences are that one set offers an A6M5 Zero, while the second set is the A6M5b Zero. The -b Zero featured various upgraded avionics within the cockpit. Comparing the two sets, minor differences are seen, including different controls and avionics boxes. As with all Aires sets the castings are well done and are cast in grey and beige resin. While the casting in grey resin was excellent in my samples, the beige castings featured quite a bit of flash, and did not seem to have the crisp detail that Aires is known for. In my opinion, this is not a fault of Aires, but more due to the type of resin used.

Review Author
Robert Folden
Published on
October 13, 2011
Company
Quickboost
Scale
1/32
MSRP
$21.95

One of the leaders in resin detailing parts, Aires recently released a detail set for the wheel bay of the Tamiya 1/36 A6M5 Zero. Cast from resin, with no flash or flaws, the set comes with the two main gear bays, detail parts, and partial gear doors. As with all Aires sets the detail is superb. I did not have the Tamiya kit on hand to compare to, but a comparison to the 21st Century Zero kit showed a serious improvement over the kit bays. It is also noted that the Aires parts do fit the 21st Century kit (it was rumored that the 21st Century kit had detail copied from Tamiya).

Once again, I am very impressed with Aires’ latest release. They have an eye for detail, and an amazing skill for casting resin parts. This is one highly recommended resin set. My thanks to Aires for providing an excellent sample for review.

Review Author
Robert Folden
Published on
October 13, 2011
Company
Quickboost
Scale
1/48
MSRP
$4.99

When it comes to resin detail parts for aircraft, Quickboost is one of the top manufacturers on the market. One of their newest releases is a set of pitot tubes for the Trumpeter 1/48 Seahawk FGA Mk. 6. The set comes in finely cast resin and includes two pitot tubes and mounts. As with all Quickboost sets, the instructions simply list which parts from the kit to replace with the resin parts

As with every Quickboost set I have worked with, the parts are free of defects and flash, and are easily removed from the pour plugs, with little clean-up. This is a must-have detail set for anyone working with the Seahawk FGA kit. My thanks to Quickboost for providing the review sample

Review Author
Roger Rasor
Published on
October 13, 2011
Company
Quickboost
Scale
1/32
MSRP
$6.50

Quickboost has added a new resin item to their growing line of aftermarket parts for 1/32 aircraft. Set 32 112 will add detail to the Kinetic, Italeri or Hasegawa 1/32 F-86F kits. This set provides two ready-to-install pitot tubes cast in a flexible gray resin that likely will survive occasional bumps sometime experienced when a finished model is handled. As the photo below shows, the pitot tubes are molded on a common casting block with extended bars that protect the parts from damage in the package. These parts exhibit a much better detail than those included in the kits.

A sharp #11 x-Acto blade can be used to remove each pitot tube from the casting block. This part is a direct replacement for a kit part, but there is no molding seam to remove as is usually the case with injection molded kit parts. Because this part is cast in resin, it should be attached with super glue or epoxy cement.

Book Author(s)
Warren E. Thompson
Review Author
Floyd S. Werner Jr.
Published on
October 12, 2011
Company
Specialty Press
MSRP
$24.95

Editor's note: This publication is also available in a downloadable version from the publisher.

As a Desert Storm veteran, it was quite a unique thing the first time I actually saw an F-117 in the air. The initial raids against Baghdad brought to light the existence of these stealth fighters and their capabilities. Firsthand accounts of air combat have always been a favorite read of mine. This book was right up my alley.

This soft bound book features 200 pages of accounts from the pilot, ground crew and commander’s perspective during the war. The book features many previously un-published black and white photos. These will be helpful and informative for the modeler. Every photo comes with an extensive caption that provides insight.